Meet the H7 and H7 RGB+: Built to Be Seen

The glass does not stop at the corner. Or at the top.

The H7 is a single-chamber ATX mid-tower wrapped in glass. Front and side are one piece, curved rather than joined, so nothing at the corner breaks the line. Both models then ship in Vista Mode, with the top cut to the same radius, so the glass carries over the top edge.

It comes two ways. The H7 arrives without fans, ready for the cooling you choose. The H7 RGB+ comes with two F420 RGB Reverse single-frame fans, an F140 RGB fan and a Control Hub Lite already installed and wired. Same chassis, same glass, same day.

Here is what went into it.

Front to side to top

NZXT H7 in white, installed in a build, with the glass top

Holding a curve through tempering is a tolerance problem, and so is cutting the top to match that radius closely enough that the transition reads as continuous. Get both right and the corner disappears, and the top reads as part of the same curve. Opposite the glass, the right panel is steel mesh with a nylon dust filter.

Two tops, one case

NZXT H7 in black, exploded view showing both top panels, the glass and the steel chassis

The glass top is fitted out of the box, and a steel mesh panel with its own fan bracket ships beside it. Swap the mesh in and the top mounts open up for a radiator up to 420 mm — a glass showcase or an airflow build from the same chassis, without buying a part. The angled bottom fan bracket is in there too.

Made to show off

NZXT H7 in black, installed in a build, with the glass top

That angled bracket turns the bottom fans out toward the glass rather than straight up, and vertical GPU mounting turns the graphics card the same way. A lit NZXT logo sits on the side panel in white. On the H7 RGB+ the fans are already mounted and wired to the Control Hub Lite, so lighting and fan curves are set in NZXT CAM from the first boot.

Clean, start to finish

NZXT H7 in black, right panel removed, showing the cable routing space behind the motherboard tray

Back-connect motherboard support puts every power connector behind the tray, and a dedicated channel takes the AIO tubing out of the sightline — its cover lifts out if you would rather show the tubing. The mesh panels, top and side, come away by hand, nylon dust filters sit on the right side and the bottom, and the front I/O carries USB-C, two USB-A ports and a headset jack.

Room for the biggest hardware

NZXT H7 RGB+ in white, installed in a build, with the mesh top

Behind the glass there is room for a graphics card up to 495 mm (with a 30 mm front-right fan), held level by an integrated adjustable anti-sag bracket, and for a radiator up to 420 mm on the right side — or on the top once the mesh is fitted.

What changed from the H7 Flow (2024)

Front and left side — a mesh front and a flat tempered glass side meeting at a corner → one curved glass panel across both, with no seam
Top — steel mesh with a 360 mm top radiator → glass as standard, with a steel mesh alternative in the box that takes a 420 mm radiator
Room — 62.1 L → 75.2 L; graphics cards 410 → 495 mm (with a 30 mm front-right fan), on an anti-sag bracket that is new this generation; CPU air coolers 185 → 188 mm
Motherboards — back-connect support is new; E-ATX is no longer supported, where the 2024 H7 Flow took it up to 277 mm
Front I/O — the same two USB Type-A, one USB Type-C and headset jack, moved off the top panel to the front
Fans — the H7 Flow included three F120Q fans and the H7 Flow RGB an F360 RGB Core → the H7 comes with none, ready for the cooling you choose; the H7 RGB+ arrives with two F420 RGB Reverse fans, an F140 RGB and a Control Hub Lite, installed and wired

Which one

Bringing your own fans, or planning the cooling out yourself? Start with the H7. Want the lighting settled on day one, ready to tune in NZXT CAM from the first boot? Take the H7 RGB+.

Availability

The H7 and H7 RGB+ come in all-black and all-white and are rolling out to authorized retailers worldwide over the coming months. Availability varies by region and store.